Montigo L-Series DF-ST Installationsanleitung PDF herunterladen (Seite 16)

Page 16

L-Series DF-ST See-thru Gas Fireplace

Part No. XG0812

f i r e f e a t u r e

Page 16

Part No. XG0180

Maintenance

WARNING:

Do not attempt to clean glass when hot.

Do not clean glass with abrasive materials as any glass

etching may cause premature glass failure.

CAUTIONS

Fireplace gas control must be in the “OFF” position

and pilot and main burners extinguished when cleaning

appliance with a vacuum.

Doors and logs can get very hot. Handle only when

cool.

General

Have the replace and installation inspected yearly. The inspection

must include, but is not limited to, the following:

• A visual check of the entire vent system and termination.

• An inspection of the explosion relief appers and the door

gasketing to ensure a proper seal.

• An inspection of the burner, venturi, and primary air openings.

• An inspection of the gas valve, gas components, and pilot ame.

For your convenience a 1/8" manifold pressure tap is supplied

on the gas valve for a test gauge connection. See Figure 32.

• Inspection of all optional equipment; fans, thermostats, etc.

For Natural Gas this appliance requires a minimum inlet pressure

of 5.5" W.C. and a manifold pressure of 3.5" W.C.

For Propane Gas this appliance requires a minimum inlet pressure

of 11" W.C. and a manifold pressure of 10" W.C.

Always keep the replace area clear and free of combustible materials,

as well as gasoline and other ammable vapors and liquids.

Do not use this appliance if any part has been under water. Immediately

call a qualied service technician to inspect the appliance and to

replace any part of the control system and any gas control which

has been under water.

Operation

Lighting Instructions

See pages 11 to 15.

Burner Adjustment

The L-Series DF is equipped with an adjustable burner, allowing you to

raise or lower the ames. To adjust the ames, locate the black knob

marked 'Hi-Lo', in the centre of the gas control valve (See Figure 32).

The front burners are not adjustable.

To raise the ame height, turn the black knob (located behind the

lower trim) counter-clockwise.

To lower the ame height, turn clockwise.

Figure 32. 'Hi-Lo' Adjustment on the L-Series DF's gas valve.

Cleaning

When the replace is rst activated, there may be some smoking and

a visible lm may be left on the glass. This is a normal condition, and is

the result of burning of protective coatings on new metal.

Glass must be cleaned periodically to remove any lm (which is a

normal by-product of combustion) which may be visible. Film can

easily be removed by removing the door, as shown on page 12.

Handle the door carefully, and clean it with non-abrasive glass

cleaners. One of the most effective products is Kel Kem.

Silicone seals on inner door during initial ring will "off gas", leaving

a visual deposit of a white substance on combustion chamber walls.

This can easily be removed using normal household products.

Use a vacuum cleaner or whisk broom to keep the control

compartment, burner, and rebox free from dust and lint.

Linear Burners may be cleaned periodically with a vacuum to remove

soot or other contaminates.

Note: L-Series DF-I models (electronic ignition) do not

feature hi/lo adjustment.

'Hi-Lo' Adjustment Knob

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Montigo L-Series DF-ST Installationsanleitung Seite 16

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Montigo L-Series DF-ST