Montigo L-Series DF Installationsanleitung PDF herunterladen (Seite 7)

Page 7

L52-DF Gas Fireplace

Part No. XG0180

f i r e f e a t u r e

Installation

Top Vent Venting Runs

For the L52-DF Top Vent, there are two types of installations: A)

Through-The-Wall Installations and B) Vertical (Through-The-Roof)

Installations.

A) Through-The-Wall Installations

Before you install any venting, you must determine whether the venting

run will be acceptable. Unacceptable venting can affect the replace's

combustion.

The Venting Graph

Measure the vertical height from the replace hearth to the centre of

the termination and the horizontal run from the from the replace ue

collar to the wall ange of the termination. Plot on the Venting Graph

(Fig. 9a) with an 'X'.

If the 'X' falls on or above the top boundary of the shaded area, the

installation is acceptable.

Example A: (Acceptable Installation)

If the vertical dimension from the hearth is 84" and the horizontal run to

the wall ﬂange of the vent termination is 36", this would be an acceptable

installation.

Example B: (Acceptable Installation)

If the vertical dimension from the hearth is 108" and the horizontal run to

the wall ﬂange of the vent termination is 120", this would be an acceptable

installation.

Example C: (Unacceptable Installation)

If the vertical dimension from the ﬂoor of the ﬁreplace is 48" and the

horizontal run to the wall ﬂange of the vent termination is 108", this would

NOT be an acceptable installation.

Figure 9c. L52DF Top Vent Venting Graph

NOTES:

All dimension lengths for vertical or horizontal runs are

measured from centre of the vent pipe.

Venting runs must fall within the limits set by the venting

graph (see Figure 9a).

Available Top Vent Components

The following venting components are available for the L-Series DF

Top Vent:

5" / 8" Venting

A - Termination PTO-3 (3" Length)

PTO-3F (3" Length)

B - Stucco Kits MSR (Stucco Frame)

MOSR (Stucco Can)

BSR ( Brick Can)

C - Flex Sections PFL-1 (12" Section)

PFL-2 (24" Section)

PFL-3 (36" Section)

PFL-4 (48" Section)

D - Rigid

Sections

PEXT-1 (12" m/f Section)

PEXT-2 (24" m/f Section)

PEXT-3 (36" m/f Section)

PEXT-4 (48" m/f Section)

E - Elbows PEL-90MM (m/m 90° Elbow)

PEL-90FF (f/f 90° Elbow)

PEL-90FM (f/m 90° Elbow)

NOTES: All dimension lengths for vertical or horizontal runs are

measured from centre of the vent pipe.

Venting runs must fall within the limits set by the venting

graph (see Figure 9A).

Example 1:

For our shortest venting conguration use components A and E (see

Figure 9a).

Figure 10. Typical Top Vent installation. If the 90° elbow is installed

directly on the ﬁreplace, for height to the center of the

termination see chart on page 3.

Important:

An inspection of the explosion relief appers and door must be

made prior to lighting the replace. This will ensure the door gas-

keting material will provide an adequate seal during operation.

PEL

RHS101

1 2 3 4 5 6 7 8 9 10 11 12 ... 21 22

Kommentare zu diesen Handbüchern

Keine Kommentare

Montigo L-Series DF Installationsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Montigo L-Series DF