Montigo RX200 Bedienungsanleitung PDF herunterladen

Upgrade Kit

Proame 2 Upgrade Kit RX 200 NG/LP

Page 1

XT0016 - 092214

 The installation of this kit must be done by a qualied and

certied gas appliance installer.

 Check local codes and read all instructions prior to installation.

Ensure that all power to the appliance is off at the electrical breaker or fuse

before beginning installation. Ensure gas is turned off at the shutoff valve before

beginning installation.

CAUTION

This kit is for use with the following models:

B34DT-2-F : B34 Top Vent, Electronic Ignition, IPI

B34DR-2-F : B34 Rear Vent, Electronic Ignition, IPI

B38DT-2-F : B38 Top Vent, Electronic Ignition, IPI

B38DR-2-F : B38 Rear Vent, Electronic Ignition, IPI

Warning: If the information in these instructions is not followed

exactly, a fire or explosion may result causing property damage,

personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

 What To Do If You Smell Gas:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualiﬁed installer, service agency or

the gas supplier.

Upgrade Kit NG/LP Proame 2 (Basic to Full

Load with Remote)

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Load with Remote)

Upgrade KitProame 2 Upgrade Kit RX 200 NG/LPPage 1XT0016 - 092214 The installation of this kit must be done by a qualied and certied gas applianc

Seite 2 - Tool Required

InstallationPage 2XT0016 - 092214General InformationThis blower kit is for installation with the models listed above.KIT # ContentsRX200NG Control Mod

Seite 3

InstallationPage 3XT0016 - 092214A. Disconnect Control Module and Harness:1. Disconnect Control Module Powercord from the PPO box.Figure 3 Powercord

Seite 4

InstallationPage 4XT0016 - 092214B. Stepper Motor Installation:1. Using a Torx T20 or slotted screw driver, remove the two screws that are attached t

Seite 5

InstallationPage 5XT0016 - 092214C. Control Module Installation:1. Position the new control module on the ﬁreplace ﬂoor ( the red switch "SW1&q

Seite 6

InstallationPage 6XT0016 - 092214Figure 17 Attach switch bracket to front of replaceD. Main ON/OFF Switch Installation:1. Position the Main/oﬀ Switc

Seite 7

InstallationPage 7XT0016 - 092214F. Operation with Backup Battery:1. Install the four supplied AA batteries to the battery holder.CAUTION: Please no

Seite 8 - RX 200 NG/LP

XT0016 - 092214Proflame 2 Upgrade KitRX 200 NG/LP

Kommentare zu diesen Handbüchern

Keine Kommentare

Montigo RX200 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Zuhause Montigo RX200 herunter. Montigo RX200 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Zuhause Montigo RX200